Main Menu Vehicle Trails Mechanicals TJ/LJ Mods JK Mods Gallery
Additional Parts

Additional parts

Well during the install I discovered that you need to fabricate a few extra parts that RE doesn't address, also a few parts that need to be corrected because RE wasn't paying attention.  I will update this page as I get the parts finished.  If you already read my Issues page, you will know about some of my concerns.  These pictures were taken during prototyping so my not reflect my directions exactly.

Brake Line Standoff Installation

Additional Parts:
As Needed
Tools Needed:
Drill
As Needed

 

Compressor Relocation: (Not fully satisfied with this install)
1. You will need to flip this over so that you can bolt it into the bottom of the body.  You may need to disconnect the electrical connectors buy first pulling out the little red tab and the disconnecting them.  I just pried the trees out of the bracket to get the other part off. Dsc01593.jpg (171209 bytes)
2. You will also need to pry the tree holding this mass of wires and hoses to the top transfer case off to give you the extra slack you need to relocate this.   Dsc01651.jpg (176335 bytes)
3. I fabricated a bracket, (Opps drilled holes in wrong spot), to allow the compressors to sit as close as you can get them to the transfer case (not much slack in the hoses).  Once I had the bracket bolted up, I just used some self drilling screws and screwed the other end into the body. Dsc01685.jpg (188635 bytes)
4. I'm not very happy with this solution, so when I have time, I will either build a skid plate and remount them in the stock location, or figure out something else to do.


Additional Parts:
None
Tools Needed:
Pipe Bender
Level
Angle Gauge

 

Front Track Bar Correction: (For Dana 44 only)
1. I measured the bend points on the RE 1600 bar and then clamped my Track bar in the pipe bender.  The RE 1600 bar is bent off at an angle from centerline.  My track bar didn't need this, so I needed to make absolutely sure that the bend I was putting in was along the centerline.  I used a level and an angle gauge to make certain that the axle side mount was aligned correctly.  I then bent the bar so that it matched the angle already on the bar.  I won't put out the measurements and angles, e-mail me if your interested in attempting this.  Remember if you screw it up, you'll need a new bar. Dsc01827.jpg (165371 bytes)
2. As you can see I now have plenty of clearance around the differential with this bent bar. Dsc01828.jpg (195257 bytes)

Next Page

Skid Plate
Brake Line Standoffs
Long Arms
Front End
Rear End
Additional Parts
Magna-Flow Muffler
Tom Woods Drive Shaft
Issues
Final Notes

This page last updated: 16-Apr-2008

Content and Design © 2002-present WanderingTrail,  Ronald Seegert
Common Sense and Safety should always be observed when working on your vehicle or doing modifications. Jackstands, wheel blocks, disconnecting the battery are a few of the basic safety precautions that should be used and may not be mentioned in the write ups on this site. You are responsible for your own installation, these write ups are a helpful guideline and should not be taken as an official installation instruction. My write up may be different from the kits currently out there, so alwasy double check the manufacturers installation instructions when installing anything. I try to keep the site up to date with changes that have occured as I discover them, but may not have the latest unless someone lets me know. If you feel that an install is above your capabilities after reading my write ups, I recommend getting together with a club and getting some help. Only a few times have I needed to employe some actual help from a shop to get something done. Usually welding or A/C work. While I have spent many years working on mechanical systems, I am not an expert, nor do I pretend to be one. I hope these write ups have been useful to you.
All trademarked names & logos are property of their respective owners
This site is in no way associated with FCA.
Jeep is a registered trademark of FCA.

16-Apr-2008